XTH 3000-12, XTH 5000-24, XTH 6000-48, XTH 8000-48
The Xtender series provides unmatched freedom of use due to its many functions. In a basic application, it offers a total package: the functions of inverter, battery charger, transfer system and assistance to the source. These functions can be combined and controlled in a totally automatic way for exceptional ease and optimal management of available energy.
The Xtender is equipped with a command entry and 2 configurable auxiliary contacts. This allows automatic control of a genset or loadshedding when the battery voltage is too low. The flexibility obtained makes it possible to implement special functionalities, often necessary for good energy management in standalone systems.
The Xtender series offers an optimal use of all sources that can be found in hybrid systems, whatever their connecting mode (AC or DC bus), up to the nominal power of the Xtender system (single, parallel and/or three phase).
Function Smart-Boost and active filtering
With this function it is possible to interact directly with the AC source (Genset or grid) and to implement some basic functions such as:
• Efficient and immediate limitation of the current of the source, including non linear or inductive/ capacitive loads, protecting efficiently the breakers during connection to shore power or to a camping power meter with limited current (function of power shaving and power assistance) (more information on our website and in the Application note AN001/www.fangpusun.com).
• Power shaving of load steps on the generator allowing an optimal sizing of the generator and asssuring the best possible efficiency of the fossil fuels (function of filtering and of power assistance).
• The function of assistance to the source enables also to implement advanced functions such as the priorityuse of renewable energy, even when the grid is available (more information on our website and in the Application note AN002/www.fangpusun.com)
|Model||XTH 3000-12||XTH 5000-24||XTH 6000-48||XTH 8000-48|
|Characterisation of the operating performance|
|Nominal battery voltage||12V||24V||48V||48V|
|Input voltage range||9.5-17VDC||19-34VDC||38-68VDC||38-68VDC|
|Power 30 min.||3000VA||5000VA||6000VA||8000VA|
|Power 5 sec.||7.5KVA||12KVA||15KVA||21KVA|
|Own consumption stand by||1.4W||1.8W||2.2W||2.4W|
|Own consumption ON||14W||18W||22W||30W|
|Acoustic level without ventilation||40 dB|
|Acoustic level with ventilation||45 dB|
|Maximum load||Up to short-circuit|
|Maximum asymmetric load||Up to Pcont.|
|Load detection (stand-by)||2 to 25 W|
|Output voltage||Pure sine wave 230Vac (±2%) / 120Vac (1)|
|Output frequency||45Hz - 60Hz (1) ± 0.05% (crystal controlled)|
|Overload and short-circuit protection||Automatic disconnection with 3 time restart attempt|
|Overheat protection||Warning before shut-off - with automatic restart|
|Charge Characteristic||6 steps : Bulk-Absorption-Floating-Equalization-reduced fl oating-periodic absorptionNumber of steps, thresholds, end current and times completely adjustable with the RCC-02/-03|
|Temperature compensation||With BTS-01 or BSP 500/1200|
|Power Factor Correction (PFC) according||EN 61000-3-2|
|Maximum charging current||160A||140A||100A||120A|
|General data||XTH 3000-12||XTH 5000-24||XTH 6000-48||XTH 8000-48|
|Input voltage range||150 to 265Vac / 50 to 140Vac (1)|
|Input frequency||45 to 65Hz|
|Input current max. (transfer relay) /Output current max.||50Aac/56Aac||50Aac/80Aac|
|Multifunction contacts||2 independent contacts (potential free 3 points, 16Aac/5Adc)|
|Dimension hxwxl [mm]||230x300x500|
|Operating temperature range||-20 to 55°C|
|Relative humidity in operation||95% without condensation|
|Ventilation||Forced from 55°C|