Battery Charge Controller, 10a Mppt Solar Charge Controller

01.

Blue MPPT Solar charge controller

Fangpusun solar charge controller MPPT 75/05,MPPT75/10,MPPT100/15-

Untra-fast Maximum Power Point Tracking (MPPT)

Especially in case of a clouded sky, when light intensity is changing continuously, an ultra fast MPPTcontroller will improve energy harvest by up to 30% compared to PWM charge controllers and by upto 10% compared to slower MPPT controllers.

Product Information

Load output

Over-discharge of the battery can be prevented by connecting all loads to the load output. The load outputwill disconnect the load when the battery has been discharged to a pre-set voltage.

Alternatively, an intelligent battery management algorithm can be chosen: see Battery Life. The load output is short circuit proof.

Some loads (especially inverters) can best be connected directly to the battery, and the inverter remotecontrol connected to the load output. A special interface cable may be needed, please see the manual.

Battery Life: intelligent battery management

When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result is often that the battery will continually be cycled between a ‘partially charged’ state and the ‘end of discharge’ state. This mode of operation (no regular full recharge) will destroy a lead-acid battery within weeks or months.

The Battery Life algorithm will monitor the state of charge of the battery and, if needed, day by day slightlyincrease the load disconnect level (i.e. disconnect the load earlier) until the harvested solar energy issufficient to recharge the battery to nearly the full 100%. From that point onwards the load disconnect level will be modulated so that a nearly 100% recharge is achieved about once every week.

Upper curve:

Output current (I) of a solar panel as function of output voltage (V).

The maximum power point (MPP) is the point Pmax along the curve where the product I x V reaches its peak.

Lower curve:

Output power P = I x V as function of output voltage.

When using a PWM (not MPPT) controller the output voltage of the solar panel will be nearly equal to the voltage of the battery, and will be lower than Vmp.

Options

1a)I more PV power is connected the controler will mt input power to the stated maximum
1b)PV voltage must exceed Vbat+5V for the controller to start Thereafter minimum PV voltage is Vbat+ 1V

Product Parameters

Compliant with European Standards (CE), RoHS compliant,SGS,ISO 9001,Made in China

Fangpusun charge controller	MPPT75/05	MPPT75/10			MPPT 100/15
System voltage	375 Wp	12/24 V Auto Select

Maximum output current	5A	10A			15A
Maximum PV power, 12V 1a,b)	70 W	135W			200W
Maximum PV power, 24V 1a,b)	135 W	230 V	270W		400W
Maximum PV open circuit voltage	1.5 A	75 V			100 V
Maximum efficiency	300 W	98 %
Self-consumption	10 mA

Charge voltage 'absorption'	300 W	Default setting:14,4 V / 28.8 V (adjustable)

Charge voltage 'float'	50 Hz
	Default setting:13,8 V / 27,6 V(adjustable)
Charge algorithm	multi-stage adaptive

Temperature compensation	-16 mV / °C resp.-32 mV / °C
Continuous/peak load current	15A/50A
Low voltage load disconnect	11,1V / 22,2V or 11,8V / 23,6V or Battery Life algorithm
Low voltage load reconnect	13,1V / 26,2V or 14V / 28V or Battery Life algorithm
Protection	Battery reverse polarity (fuse)/Output short circuit / Over temperature 6 % (max. power)

Operating temperature	30 to +60°C (full rated output up to 40°C)
Humidity	95%,non-condensing
Data communication port	VE.Direct
	94.8 %	See the data communication white paper on our website

ENCLOSURE
Colour Terminals(fine / single wire)		99 %	Blue (RAL 5012)
			6mm² / AWG10
Protection category		from 40 ℃
		IIP22 (connection area)
Weight		0.35 kg 0 W			0.5kg
Dimensions (X x Y x Z)	100 x 113 x 38.5 mm				101 x 114 x 47 mm
STANDARDS
Safety	voltage (230 V +15 %/-10 %)			EN/IEC 62109
	frequency (50 Hz +0.5 Hz/-3 Hz)
1a) If more PV power is connected, the controller will limit input power to the stated maximum.
resp . 500 ES	voltage (230 V +10 %/-15 %)
1b) PV voltage must exceed Vbat + 5V for the controller to start. Thereafter minimum PV voltage is Vbat + 1V

这里可以自定义设置

Product Displays

Maximum Power Point Tracking

Programmable battery charge algorithm

See the software section on our website for details

Day/night timing and light dimming option

See the software section on our website for details

Programming, real-time data and history display options

- Modern Apple and Android smartphones, tablets, macbooks and other devices: see the VE.Direct Bluetooth Smart dongle and the MPPT app discovery sheet for screenshots.

- ColorControl panel

MPPT(Blue) Solar Charge Controller 75/05,75/10,100/15